What Type of Welding Is Used for Aluminium?

Welding aluminium requires different welding techniques, different shielding gases, different specifications, and different pre-weld and post-weld processing than welding steel. The welding processes that are fit to weld both may require alterations so that they can be used to weld aluminium. Aluminium can be welded with relative ease, but first and foremost, the correct welding process must be selected.

Why Is Welding Aluminium Difficult?

Before highlighting different welding processes that are used for joining aluminium, it is important to understand some of the difficulties that are inherent to welding aluminium. One area of difficulty is filler metal. First, some aluminium alloys cannot be welded without filler materials. Alloys such as 6082 will lose strength at the weld if welded without filler metal. Furthermore, the correct filler material must be selected otherwise there could be a weld failure. For example, if welding 6082 to 7005 then 5356 alloy wire should be used. When welding 6082 to itself, use 4043 alloy wire. Another challenge with aluminium filler metal is feeding. If a mechanical wire feeding process is being used, special drive systems will most likely be needed. This is because aluminium has less column strength than steel, and will more than likely buckle and tangle if special wire drive systems, such as a push-pull gun, are not used. This is especially true for thinner aluminium filler metals (i.e. 0.8 mm or 1 mm diameter).

Aluminium also has a greater thermal conductivity than steel. The heat created when the welding process is initiated on aluminium is dispersed more rapidly than when welding an iron-based alloy. Therefore, full penetration may not occur until the weld has progressed quite far from the start. This is known as a cold start. Care must be taken so that cold starts do not occur when welding aluminium. Another result of the increased thermal conductivity is larger craters. By the time the end of the weld is reached, more heat is present than at the start. This heat disperses well in aluminium and can create a large crater. Aluminium is very susceptible to crater cracking, therefore, craters should be filled in so that failure does not occur at the end of a weld.

Aluminium also requires different pre-weld and post-weld processing. Aluminium forms an oxide layer that has a higher melting temperature than the actual aluminium itself. In order to avoid un-melted aluminium oxide particles in the weld, an oxide removal process, such as wire brushing or chemical cleaning, should be used prior to welding. Several aluminium alloys, such as 6082-T6, are artificially aged to increase their strength. The heat from welding ruins the benefits gained by artificial aging, and large reductions in strength will be found in the heat-affected zone. Therefore, post-weld artificial aging may be required for alloys such as these.

What Type of Welding Is Used for Aluminium?

The following are welding processes that can be used for aluminium:

• GTAW/TIG
• GMAW/MIG
• Laser Beam Welding and Electron Beam Welding
• Resistance Welding

GTAW/TIG

One of the most popular welding processes for aluminium is gas tungsten arc welding (GTAW), otherwise known as tungsten inert gas (TIG) welding. GTAW is a great process for aluminium because it does not require mechanical wire feeding, which can create feedability issues. Instead, the filler material is fed into the puddle by the welder with his hand. Also, the GTAW process is extremely clean, which prevents aluminium from being contaminated by the atmosphere.

GMAW/MIG

Gas metal arc welding (GMAW), or metal inert gas (MIG) welding is another great choice for welding aluminium. Gas metal arc welding generally has higher deposition rates and faster travel speeds than GTAW. However, GMAW uses a mechanical wire feeding system. Because of this, a push-pull gun or spool gun may be needed so that aluminium wire feeding is possible. Also, it is important to not use 100% CO2 or 75% Argon/25% C02 shielding gas. Such gas is a viable choice for steel, but aluminium cannot handle the reactive C02 gas. Follow the filler metal manufacturer recommendations for shielding gas type.

Laser Beam Welding and Electron Beam Welding

Beam welding processes are often quite capable of welding aluminium. Also, since the power density of beam welding processes are so high, cold starts are less of a concern. With laser welding, material light reflectivity can be a concern. Also, shielding gas optimization is key to avoid porosity. Electron beam welding generally does not have these problems because it does not use light as an energy medium and it is performed in a vacuum.

Resistance Welding

Resistance welding is a possibility when welding aluminium. However, difficulties arise from the electrical and thermal conductivity of aluminium. Parameter development time may be significant and special tips and resistance welding equipment may be required to overcome these challenges.

Processes That Are Not Recommended For Welding Aluminium

There are several processes that are not well suited for welding aluminium. Any welding process that uses a flux, such as stick welding, flux cored arc welding, and submerged arc welding, are generally not effective methods for welding aluminium. Oftentimes, the welds created by these processes result in large amounts of porosity.